Author: wiperfoamball

  • 6 in Natural Rubber Foam Wiper Balls for Cementing – Abu Dhabi

    6 in Natural Rubber Foam Wiper Balls for Cementing – Abu Dhabi

    6 inch natural rubber foam wiper ball for cementing - foam wiper ball Abu Dhabi supply by MERIT

    Foam Wiper Ball Abu Dhabi: 6 Inch Natural Rubber Foam Wiper Balls for Cementing

    Looking for a reliable foam wiper ball Abu Dhabi supplier for your next cementing job? MERIT manufactures 6 inch natural rubber foam wiper balls in Istanbul and delivers them DAP to Abu Dhabi in about 15 days. Every shipment comes with a Certificate of Conformance carrying your PO number.

    MERIT serves the MENA market and works with suppliers of general and mechanical products to large operators in the region. Our main focus is meeting the requirements of ADNOC and its supply chain, from specification to documentation.

    This guide explains what a 6 in foam wiper ball does, the specification buyers in the UAE oil and gas sector ask for, and how to order one that passes inspection the first time.

    What is a foam wiper ball?

    A foam wiper ball used in Abu Dhabi cementing jobs is a soft, compressible sphere made of natural rubber foam. It is pumped through the drill pipe, compresses to the pipe ID and wipes the inner wall as it travels.

    On a cementing job it does three things:

    • Wipes cement off the drill pipe after a balanced cement plug.
    • Removes the mud film from the string before cementing starts.
    • Separates fluids during displacement, so cement and mud do not mix.

    Because the foam is highly elastic, the ball squeezes through restrictions as small as 0.875 in (22.2 mm) and then recovers its shape.

    Foam wiper ball Abu Dhabi specification: 6 in natural rubber foam

    Operators in Abu Dhabi typically describe this item in purchase requisitions as BALL,WPR,NTRL RBR FOAM,6IN, with these characteristics:

    Requisition characteristicRequirementMERIT WP10006
    ClassCementing / BallCementing foam wiper ball
    TypeWiperWiper ball
    MaterialNatural rubber foamNatural rubber (cis-1,4-polyisoprene) foam, sulphur vulcanised, closed-cell
    Size6 in6.00 in nominal (152.4 mm), 5.91 in (150 mm) actual
    InspectionCertificate of ConformanceCoC with every shipment, carrying your PO number

    When you request a quotation, quote this description and confirm that the supplier can issue a Certificate of Conformance. It saves a round of technical clarification.

    Technical data of the 6 inch foam wiper ball

    PropertyValueTest method
    Actual diameter5.91 in (150 mm), ±2%Caliper
    Wiping range (pipe ID)2.00 to 4.75 in (50.8 to 120.6 mm)–
    Minimal restriction0.875 in (22.2 mm)–
    Density0.15 to 0.25 g/cm³ASTM D1056
    Hardness40 to 50 Shore AASTM D2240
    Elongation at rupture380 to 440 %ASTM D412
    Compression set (22 h, 70 °C)< 20 %ASTM D395 / D1056
    Operating temperature-40 to +70 °C continuous, +100 °C short-term–
    Recommended pump rate3 to 6 bpm–

    The 6 in ball covers the common IDs of 2-7/8 in to 5 in drill pipe, work strings and tubing. Always check the IDs of tool joints and crossovers in your string before running it.

    Why natural rubber foam works in UAE oilfields

    Natural rubber foam is the standard material for every cementing foam wiper ball in Abu Dhabi and the wider UAE, for good reasons:

    • High elongation lets the ball pass restrictions without tearing.
    • Low compression set keeps wiping performance consistent along the string.
    • Closed-cell structure means the ball does not soak up drilling fluid.
    • Good compatibility with water-based mud, brines and cement slurry.

    For hot wells or oil-based mud, ask for our HTR (high-temperature, up to +150 °C) or SRF (oil-resistant) grades.

    Certificate of Conformance and documentation

    Inspection requirements in Abu Dhabi tenders often call for a Certificate of Conformance. MERIT issues one with every delivery under our ISO 9001:2015 quality system.

    The CoC states the part number, description, quantity, batch number and manufacture date. It certifies that the balls conform to your PO and to our technical datasheet, and it is signed and stamped by Merit Quality Control.

    Each shipment also includes a commercial invoice, packing list, certificate of origin and material test certificate with batch traceability.

    Delivery to Abu Dhabi and the UAE

    We ship every foam wiper ball to Abu Dhabi directly from our factory in Istanbul, Turkiye, and also deliver to other locations in the UAE and the wider MENA region. Our terms are set up for suppliers who serve ADNOC and other large operators.

    • Incoterm: DAP Abu Dhabi (Incoterms 2020) – we deliver to your door.
    • Lead time: about 15 days from receipt of PO.
    • Packing: each ball individually wrapped and packed in export wooden crates.
    • Fresh production: every order is made new, so you never receive aged stock.

    How to order a foam wiper ball in Abu Dhabi

    1. Send us your RFQ with item description, size and quantity.
    2. Tell us your pipe IDs if you would like a sizing check.
    3. Receive our commercial and technical quotation with datasheet, drawing and catalogue.
    4. Issue your PO, and we start production.
    5. Receive the goods in Abu Dhabi with the Certificate of Conformance.

    Frequently asked questions

    What size foam wiper ball do I need for 5 in drill pipe?

    A 6 in nominal foam wiper ball suits pipe IDs from 2.00 to 4.75 in, which covers most 2-7/8 in to 5 in drill pipe. Send us your exact IDs for confirmation.

    Is a foam wiper ball a pressure barrier?

    No. It is a wiping and fluid separation tool only. It does not replace top or bottom cementing plugs or drill pipe darts.

    Do you supply a Certificate of Conformance?

    Yes. Every shipment includes a CoC with your PO number, issued under our ISO 9001:2015 quality system.

    How long does delivery to Abu Dhabi take?

    Your foam wiper ball order reaches Abu Dhabi in about 15 days from receipt of PO, delivered DAP.

    What is the shelf life of a foam wiper ball?

    24 months from manufacture, stored indoors at 10 to 25 °C, away from sunlight, ozone and hydrocarbons.

    Request a quotation

    Need a foam wiper ball in Abu Dhabi for your next cementing operation, or supplying ADNOC and other operators across the MENA region? Send your RFQ to info@foam-wiper-ball.com or message us on WhatsApp at +90 552 105 10 34. You will receive a full commercial and technical quotation with datasheet and drawing.

  • MERIT Foam Wiper Balls: Revised Technical Data Sheet (Rev. 2.0) Now Available

    MERIT Foam Wiper Balls: Revised Technical Data Sheet (Rev. 2.0) Now Available

    MERIT natural rubber foam wiper balls for oilfield cementing

    A clearer data sheet for a simple, critical tool

    MERIT has released Revision 2.0 of the Technical Data Sheet for its cementing foam wiper balls (document TDS-FWB-001, issued 21 October 2026). It replaces Version 1.0 from April 2025 and is free to download.

    A foam wiper ball is one of the cheapest items on a cementing job, but choosing the wrong one costs rig time. Too small, and mud film and cement stay on the pipe wall. Too large or too stiff, and the ball can stall at a float collar or stage tool. Engineers need exact numbers to choose correctly, and Rev. 2.0 puts those numbers in one place.

    The new edition is a 32-page reference covering specifications, sizing, material science, deployment, performance, storage, safety and ordering.

    What’s new in Revision 2.0

    • Full size table, 3 in to 20 in. All 18 standard sizes (WP10003 to WP10020) now list actual diameter, typical wiping range and minimal restriction, in both inches and millimetres. 1 in and 2 in balls are available on request.
    • Corrected conversions. Every inch/mm value has been recalculated, so the metric and imperial columns now match exactly.
    • High-Temperature Rated (HTR) grade. A heat-stabilised closed-cell compound for continuous service from +70 °C up to +150 °C (302 °F), with part numbers for every size.
    • Clear temperature limits per grade. Standard foams are rated -40 °C to +70 °C continuous; the HTR grade covers hotter wells.
    • Honest chemical compatibility data. Exposure tolerances for water-based, oil-based and synthetic-based muds, brines, cement slurries, acids and alkalis, with a recommended grade for each.
    • Step-by-step sizing and deployment guidance, including a troubleshooting table for stalled, early or missing balls.
    • Updated references. Test methods are tied to recognised standards (ASTM D1056, D2240, D395, D412, D624).
    • Quality credentials. MERIT is ISO 9001:2015 certified (Certificate No. QA/TR/9001/2343, QA Technic).

    Four grades, one natural rubber platform

    Every MERIT wiper ball is moulded from natural rubber (cis-1,4-polyisoprene). Natural rubber gives very high resilience, so the ball squeezes through restrictions and recovers its shape, and it stays flexible down to -40 °C.

    Grade Part no. example Hardness (Shore A) Continuous temperature Best for
    Closed-cell (standard) WP10006 40–50 -40 °C to +70 °C General cementing and displacement, water-based fluids
    Semi-rigid (SRF) WP10006-SRF 50–60 -35 °C to +80 °C Heavier wiping, cement residue, oil-based mud, abrasive duty
    Open-cell (OCF) WP10006-OCF 30–40 -40 °C to +65 °C Irregular bores, drying and swabbing
    High-temperature (HTR) WP10006-HTR 45–55 -30 °C to +150 °C Hot wells above +70 °C

    One honest note: natural rubber swells in oil- and synthetic-based mud. It performs well for the short exposure of a wiping run; for longer contact, the data sheet recommends the SRF grade and a compatibility check.

    How to size a foam wiper ball in two checks

    A wiper ball is always larger than the pipe it cleans; that oversize is what presses it against the wall. Rev. 2.0 gives two numbers per size that make selection straightforward.

    1. Wiping range: the pipe IDs the ball wipes effectively. Every ID the ball must clean has to fall inside this range.
    2. Minimal restriction: the smallest opening the ball can be pumped through and still recover. The tightest restriction in the string must be equal to or larger than this value.

    Worked example. A tapered string of 5 in drill pipe (ID 4.276 in) and 3½ in drill pipe (ID 2.764 in), with a 1.000 in restriction in a sub.

    Candidate Wiping range Covers both IDs? Minimal restriction Passes 1.000 in?
    WP10005 (5 in) 1.75–4.00 in No (4.276 in is above range) 0.750 in Yes
    WP10006 (6 in) 2.00–4.75 in Yes 0.875 in Yes
    WP10007 (7 in) 2.38–5.50 in Yes 1.000 in Yes, with no margin

    The 6 in ball (WP10006) is the best fit: it wipes both pipe sizes and keeps a margin at the restriction. Also allow for the ball shrinking under high hydrostatic pressure; the data sheet tabulates diameter reduction against pressure.

    Where foam wiper balls work, and where they don’t

    Typical applications

    • Wiping drill pipe or work string clean of mud before a cement job
    • Wiping cement out of the string after setting a balanced plug (abandonment or kick-off plugs)
    • Wiping the landing string in liner and drill-pipe-conveyed cementing
    • Separating mud, spacer, cement and displacement fluid to shorten mixing zones
    • Coiled tubing cleaning, horizontal and deviated sections
    • Geothermal and water wells, pipeline pre-commissioning and soft-deposit (wax, scale) removal

    What they are not. A foam wiper ball is a cleaning and separation tool, not a pressure barrier. It does not replace top and bottom cementing plugs, drill-pipe darts, stage-tool plugs, bridge plugs or test plugs, and it should not be relied on to signal the end of displacement. Rev. 2.0 states this limit clearly, because a correct expectation is part of a safe job.

    Made in Turkiye, traceable batch by batch

    MERIT has manufactured in İstanbul since 2005 under an ISO 9001:2015 certified quality system. Each batch is traceable to its raw material lots and process records, and ships with a material test certificate. Typical lead times for standard sizes are 1–3 working days from stock for small quantities, and 7–28 working days for larger orders. Custom diameters, colours for multi-ball trains and modified compounds are available.

    Download the data sheet

    Download the MERIT Foam Wiper Ball Technical Data Sheet, Rev. 2.0 (PDF)

    Need help matching a ball to your string, tools and fluids? Send us your pipe IDs, smallest restriction, fluid type and bottom-hole temperature, and our team will recommend a size and grade.

  • Oilfield Foam Wiper Balls: Proven Pipe Wipers, 3″-21″

    Oilfield Foam Wiper Balls: Proven Pipe Wipers, 3″-21″

    Oilfield Foam Wiper Balls at Merit

    Oilfield foam wiper balls make drilling and cementing more efficient by wiping the pipe clean and separating fluids. They remove drilling mud, cement residue and debris from the inside of drill pipe, casing and tubing, and keep fluids apart during displacement. Merit manufactures foam wiper balls from natural rubber foam in standard sizes from 3″ to 21″, and also produces custom sizes on request.

    What Is an Oilfield Foam Wiper Ball?

    A foam wiper ball is a compressible sphere pumped through the pipe string. It conforms to the inner wall, pushes residual fluids and solids ahead of it, and acts as a barrier between two fluids, such as mud and cement. Because it is made of natural rubber foam, it can stretch through float collars, packers and stage tools, then recover its shape and keep wiping.

    Why Use Foam Wiper Balls in Drilling and Cementing?

    Residue left inside drill pipe and casing can:

    • restrict circulation and flow
    • contaminate the next fluid, especially cement slurry
    • cause abrasive wear on pipe and BHA components
    • add non-productive time (NPT) and cost

    A cementing wiper ball run ahead of or behind the slurry gives you a cleaner string, better displacement and more consistent cement placement.

    Merit Foam Wiper Ball Types

    Type Part Suffix Hardness (Shore A) Operating Temp. Best For
    Closed-cell (standard) – 40–50 -40°C to +70°C Water-based, oil-based and synthetic muds
    Semi-rigid -SRF 50–60 -35°C to +80°C Cement slurries, heavier wiping
    Open-cell -OCF 30–40 -40°C to +65°C Light wiping, tight restrictions
    High-temperature rated -HTR 45–55 -30°C to +150°C Deep and hot wells, geothermal

    Key Technical Features of Oilfield Foam Wiper Balls

    • Material: natural rubber foam (cis-1,4-polyisoprene)
    • Passing stretch: 380–440%, passes through tool restrictions
    • Elongation at break: 800–950%
    • Tear strength: 35–45 kN/m
    • Compression set: <20% (24 h at 70°C)
    • Shape recovery: 95–98% after 1,000–3,000 psi
    • Temperature: up to 150°C (302°F) with HTR grade
    • Tight tolerances: diameter ±2%, density ±5%

    Foam Wiper Ball Sizes

    Nominal Size Part No. Wiping Range (in) Min. Restriction (in)
    3″ WP10003 1.10 – 2.50 0.500
    4″ WP10004 1.38 – 3.12 0.625
    5″ WP10005 1.75 – 4.00 0.750
    6″ WP10006 2.00 – 4.75 0.875
    7″ WP10007 2.38 – 5.50 1.000
    8″ WP10008 3.00 – 7.00 1.375
    9″ WP10009 3.20 – 8.00 1.440
    10″ WP10010 3.51 – 8.40 1.500
    11″ WP10011 3.75 – 8.75 1.750
    12″ WP10012 4.32 – 9.00 2.000

    Larger sizes (14″, 16″, 17″, 19″, 20″, 21″) and custom diameters are available on request.

    Chemical Compatibility

    Merit wiper balls perform well in water-based muds, oil-based muds, synthetic-based fluids and completion brines. For cement slurries, we recommend the semi-rigid (-SRF) type. Specialized formulations are available for acidic environments.

    Applications

    • Drilling: drill pipe wiping, fluid separation, pressure test isolation
    • Cementing: pre-cement casing wiping, cement displacement, multistage separation, liner hanger systems
    • Production and pipelines: scale and paraffin removal, pipeline pre-commissioning
    • Geothermal and water wells

    How to Choose the Right Oilfield Foam Wiper Ball

    1. Find the largest ID the ball must wipe and check that it falls within the ball’s wiping range.
    2. Check the smallest restriction in the string against the ball’s minimum restriction.
    3. Choose the foam type for your fluid system and well temperature.
    4. Run at the recommended flow rate, for example 3–6 bpm for 3″–6″ balls and 6–12 bpm for 7″–12″ balls.

    Packaging

    Each ball is individually wrapped in anti-static, moisture-barrier packaging and shipped in export cartons.

    Order Oilfield Foam Wiper Balls from Merit

    Need help selecting a foam wiper ball for your string, tools and fluids? Download our technical data sheet or contact our engineering team by phone or WhatsApp at +90 552 105 10 34 for a fast quote.

  • 20 Inch Cementing Wiper Ball: Proven, Effective Pipe Wiper

    20 Inch Cementing Wiper Ball: Proven, Effective Pipe Wiper

    20 Inch Cementing Wiper Ball

    The 20 inch cementing wiper ball is a foam ball that wipes cement residue from the inside of 20″ pipe and casing after cementing. Pumped through the string after the cement job, it removes cement film, slurry and debris from the pipe wall and leaves the string clean for the next stage of the operation.

    What Is a 20 Inch Cementing Wiper Ball?

    A cementing wiper ball is a pipe-cleaning tool made of compressible, open-cell foam. Its diameter is matched to the inside diameter (ID) of the pipe, so when it is pumped down the string it compresses against the wall and wipes it as it travels. Our 20 inch cementing wiper ball is designed specifically for 20″ pipe and casing used in large-diameter well sections.

    How the 20 Inch Cementing Wiper Ball Works

    After the cement has been displaced, a thin film of slurry can remain on the inner wall of the pipe. If it is left in place, it may harden, reduce the internal diameter and interfere with later operations.

    The wiper ball is launched from a standard cementing head or launcher and pumped through the string. As it moves, the porous foam body compresses and seals against the pipe ID, pushing cement film, slurry and debris ahead of it. Because the foam is soft and flexible, the ball passes through the string without damaging pipe internals.

    Key Features

    • Designed for 20″ pipe and casing
    • Porous foam body compresses and seals against the pipe ID
    • Resists abrasion and both oil-based and water-based fluids
    • Passes through the string without damaging pipe internals
    • Compatible with standard cementing heads and launchers

    Applications of the 20 Inch Cementing Wiper Ball

    • Pipe and casing wiping after cementing
    • Fluid separation during displacement
    • Oil and gas wells
    • Geothermal wells
    • Water wells

    In fluid separation, the wiper ball acts as a moving barrier between two fluids, such as cement slurry and displacement fluid, and helps limit mixing at the interface.

    Material and Customization

    Every Merit 20 inch cementing wiper ball is made from high-resilience open-cell foam. The foam recovers its shape after compression, which helps it keep steady contact with the pipe wall along the string.

    Size, density, firmness and color can all be customized to suit your well conditions, fluid system and identification needs. Different colors, for example, help crews tell balls apart on site.

    Why Choose Merit Foam Wiper Balls?

    • Inspected before shipment: every ball is checked before it leaves our facility.
    • Made to your requirements: size, density, firmness and color are produced to order.
    • Help with selection: our team can help you choose the right ball for your pipe ID and application.
    • Full size range: besides the 20 inch model, we supply foam wiper balls for other pipe and casing sizes.

    Frequently Asked Questions

    What size wiper ball do I need for 20″ casing?

    The ball must match the inside diameter of your casing, which depends on its weight and wall thickness. Send us your casing weight or ID and we will recommend the right ball. Our team will confirm the size before production.

    Can the 20 inch cementing wiper ball be used with oil-based fluids?

    Yes. The foam resists abrasion and both oil-based and water-based fluids.

    Is it compatible with my cementing head?

    It is compatible with standard cementing heads and launchers. For non-standard equipment, contact us before ordering.

    Can I order a custom density or color?

    Yes. Size, density, firmness and color can be customized.

    Request Specifications and Pricing

    Download the Merit Foam Wiper Balls technical data sheet for full specifications, or contact us for pricing and lead time on the 20 inch cementing wiper ball.